Forum Post: RE: Slanting section after AT - what is this? How do you fix?
Seen it plenty. Basically the AT is stuffed .. or needs help. Check your control points first - make sure it isn't user error - picking the wrong point, using the wrong coordinates .. wrong system .....
View ArticleForum Post: RE: Production failed during photos pairwise matching.
C-drive full? When I see zips failing - first thing I check is the windows temp drive space .. bearing in mind the size of thing that is being zipped.
View ArticleForum Post: Context Capture Import Retouches Failing?
Importing Retouches fails - Exported to OBJ as instructed, Does not work. ...
View ArticleForum Post: RE: Slanting section after AT - what is this? How do you fix?
This is typical broken model with multiple components. Do a camera precalibration so camera parameters are locked and it drops photos which are not possible to tie then it will be easier to add manual...
View ArticleForum Post: RE: Slanting section after AT - what is this? How do you fix?
Thanks James this makes sense. It is a desert scene so perhaps it couldn't find enough detail. So just to clarify we didn't use any GCP's on this job. Also you suggest using tie points? So add tie...
View ArticleForum Post: Detect deadloop in PinTool
I am writing a PinTool, which can manipulate certain register/memory value. However, after manipulation, one challenge I am facing now, is the deadloop. In particular, due to the frequent manipulation...
View ArticleForum Post: RE: How to host 3mx in windows IIS server?
Don't forget to add 3mx and 3mxb in the TYPE MIME of IIS
View ArticleForum Post: RE: Slanting section after AT - what is this? How do you fix?
Hi Oto thanks for your response. To clarify what do you mean by camera calibration? On the Drone? Overlap was 80 /80 so would of through overlap is high enough? Its a sort of desert with red sand. Some...
View ArticleForum Post: RE: Slanting section after AT - what is this? How do you fix?
Hard to comment on all of this without seeing the data set in detail. 80% overlap should be enough .. that said - if you have tall trees and you are flying over the top of them at the same height - the...
View ArticleForum Post: Error in forming a 3D model
The last photo attached is an infrastructure from our site that we have to do a 3D image on. We used a DJI phantom 4 pro Drone to take pictures. It has a 13.2 mm sensor size and a focal length of 20...
View ArticleForum Post: RE: Error in forming a 3D model
Which CC version you have? It seems there is too much similarity and repeating patterns on roof so CC creates two models in one. If you did in circles then choose loop option in aerotriangulation....
View ArticleForum Post: RE: Slanting section after AT - what is this? How do you fix?
Upload some original pictures. Also you could check in automatic tie points dialog which features are used from photos it will give you idea what is going on.
View ArticleForum Post: RE: LiDAR with photogrammetry
Hello Julianna, you can see the following discussion :...
View ArticleForum Post: RE: Error in forming a 3D model
Just trying to understand your flight .. you saying you flew really low and flew an orbit .. then went up and flew a bigger orbit - same centre? And on? Not a whole lot of point as I see it - you want...
View ArticleForum Post: RE: cad to point cloud compare
Hi, MicroStation's Clash Detection module has been supporting point cloud for a few years. It should be able to clash CAD with point cloud. HTH, Mathieu
View ArticleForum Post: SIG Virtual Workshop: Bentley Reality Modeling – September 11,...
Mark your calendar and invite your colleagues to the next Bentley Reality Modeling Special Interest Group virtual workshop, Reality Modeling for Industrial Sites , on Tuesday, September 11, 2018 at 9...
View ArticleForum Post: RE: LiDAR with photogrammetry
Thank you very much! I will continue to follow this discussion and hopefully they can get everything sorted out!
View ArticleForum Post: RE: How to upload to the Web Viewer?
Just copy 3mx and its web app to IIS web folder. communities.bentley.com/.../479480
View ArticleForum Post: context capture 3d model is failed in mobile application
context capture 3D model is failed in mobile application. So how to generate reality model in mobile
View Article