Forum Post: RE: Unhandled Exception Error
i have noticed we have Bentley Rail Track on machines with the Descartes error, but not on the ones that dont have the error. is there any known issues between them?
View ArticleForum Post: RE: Unhandled Exception Error
There are no issues that we are aware (using Rail Track) of but we will test this and confirm. The problem only occurs when you try to open the Presentation Dialogue. Does this happen only when a point...
View ArticleForum Post: RE: Pointools export - Gathering data for POD never ends?
.ptl has been uploaded.. ..I think. I didn't get any verification, and a popup was blocked on our system. Please let me know if you did/didn't get it. (WestJoined.ptl)
View ArticleForum Post: RE: Pointools export - Gathering data for POD never ends?
We have the file thank you. I will get back to you shortly
View ArticleForum Post: RE: Pointools export - Gathering data for POD never ends?
The problem may be occurring as a result of your workflow. Can you raise a Service Request so that we can work on the issues with you direct? You can use the link below to access the support portal:...
View ArticleForum Post: RE: Pointools export - Gathering data for POD never ends?
Thanks Felix. I appreciate your very fast response time! While uploading I noted that this particular PTL had grown to a whopping 50MB, where it looks like my "normal" ptl's were less than 1MB....
View ArticleForum Post: RE: Pointools export - Gathering data for POD never ends?
In reply to the Service Request: It'll have to wait untill wednesday as I don't have the credentials needed at hand. My workflow is: 1. Add clouds. (Here it is a total of 3 clouds, with a total of...
View ArticleForum Post: RE: Unhandled Exception Error
the Dialog that has the issue is the Presentation under POD Dialog pulldown 'Settings', not the 'Point Cloud Presentation' in thr attributes. i can display the POD fine. Each time i want to use the...
View ArticleForum Post: RE: Pointools export - Gathering data for POD never ends?
Lets wait until Wednesday. 50MB does seem a bit large but perhaps we can find out why with more direct contact.
View ArticleForum Post: RE: Pointools export - Gathering data for POD never ends?
Ok. Wednesday it is. I just tried a few alternative ways to export, and it ends in the same (infinite?) loop where it cycles between informations displayed. Can you tell if that cycle (that happens...
View ArticleForum Post: RE: Unhandled Exception Error
Sorry my last image wasn't clear. The command I wish you to access is circled below: However, we will check for conflicts with the Bentley Railtrack installation
View ArticleForum Post: RE: Unhandled Exception Error
Can you confirm the version of Bentley Rail Track that you have installed?
View ArticleWiki Page: ContextCapture Engines stop working with “boost error: could not...
Product(s): ContextCapture Version(s): N\A Environment: N\A Area: N/A Subarea: N\A Problem Some users have reported error messages received intermittently when running the ContextCapture Engine Error:...
View ArticleForum Post: RE: work with .3mx file in Ms
Hi Alicia, I can confirm Felix's answer: I tried to attach 3mx data as a reference in MicroStation CONNECT Edition Update 1 and mentioned manipulation tools are enabled. Is there anything special in...
View ArticleForum Post: RE: work with .3mx file in Ms
Hi Jan Alicia's data was georeferenced. If you apply a Geographic Coordinate System the data cannot be manipulated using the Move, Scale and Rotate tool etc.
View ArticleForum Post: RE: work with .3mx file in Ms
[quote user="Felix James"]Alicia's data was georeferenced.[/quote] Ok, it makes the problem clear ;-) ... but not mentioned in the discussion. Regards, Jan
View ArticleForum Post: How to best fit a Solid shape to a point cloud?
Is there a function in Microstation to best fit a Solid shape to a point cloud. I am specifically looking to best fit a torus, but knowing how to best fit other shapes (cylinders, cones, slabs, etc.)...
View ArticleForum Post: Aerotriangulation block positioning
what does aerotriangulation failed to estimate block positioning means??
View ArticleForum Post: RE: Pointools export - Gathering data for POD never ends?
We raised Service Request #7000535448. Just so you know. If you find something odd and fix the project file don't hesitate to mail me :) As soon as I hear - anything at all - from you guys I'll update...
View ArticleForum Post: Failed to Load Aerotriangulation
I have tried to create a project and I get this error anyone able to help? any help would be great.(Please visit the site to view this file)
View Article